SERVICE PLATFORM &revised 2004revised 2004revised 2004revised 2004revised 2004PNEG-349REVTWO & THREEMODULE STACK DRYER MODELSSTIFFENER INSTA
10Service Platform & StiffenerPLATFORM INSTALLATION7. Use two flathead allen capscrewsand connect the center floorsupport, D61-0062, to the fronta
11Service Platform & StiffenerPLATFORM INSTALLATIONInstall the floor support anglesas follows:1. Use two flathead allen capscrewsand connect the l
12Service Platform & StiffenerPLATFORM INSTALLATIONInner Guard RailInstall the inner guard rail supportsand related parts within platformpackage n
13Service Platform & StiffenerPLATFORM INSTALLATIONFigure 15: Connecting outer front toe board to guard rail support channels.Figure 16: Connecti
14Service Platform & StiffenerPLATFORM INSTALLATION1. Connect one left-hand outer reartoe boards.2. Connect the left-hand inner reartoe board.3. C
15Service Platform & StiffenerPLATFORM INSTALLATIONFigure 19: Installing front long floor panel.6. Connect the right-hand inner toeboard.7. Place
16Service Platform & StiffenerPLATFORM INSTALLATIONFigure 21: Installation of the short wide floor panel, left-hand outer rear toeboards and hinge
17Service Platform & StiffenerPLATFORM INSTALLATIONPlatform Guard RailsUse 5/16" x 3/4" bolts and install plat-form guard rails within p
18Service Platform & StiffenerPLATFORM INSTALLATIONFigure 25, right: Installing accessdoor. Figure 26, below: Make suredoor opens freely and lies
19Service Platform & StiffenerPLATFORM INSTALLATIONFigure 27: Close-up of access door clip on guard rail.Figure 28: Check to make sure every bolt
2Service Platform & Stiffener
20Service Platform & StiffenerPLATFORM INSTALLATIONFigure 29: Finished platform on an Airstream upper module.
21Service Platform & StiffenerPLATFORM INSTALLATIONFigure 30: Ladder side view of platform on a dryer module.
22Service Platform & Stiffener PLATFORM INSTALLATIONService Platform PartsPlatform Support Channels and Floor Support AnglesQuantityPer Platform21
23Service Platform & StiffenerPLATFORM INSTALLATIONFigure 31: Breakdown of platform parts.Items 9 & 11 are nowone part.
24Service Platform & StiffenerPLATFORM INSTALLATIONFigure 32: Breakdown of platform floor parts.
25Service Platform & StiffenerSTIFFENER INSTALLATION
26Service Platform & StiffenerSTIFFENER BASKET LOCATIONFigure 33: Location of stiffener angles on basket based on lenght.
27Service Platform & StiffenerSTIFFENER EXPLODED VIEWFigure 34: Exploded view of stiffener.
28Service Platform & StiffenerSTIFFENER ASSEMBLY GeneralThis is a guide for assembling and mounting the newStack Dryer Sti
29Service Platform & StiffenerThe Second and Third Module Stiffeners are as-sembled the same way as the base module with onlyminor variations. Fo
3Service Platform & StiffenerInstallation & Safety...
30Service Platform & StiffenerEXCEPT FOR THE ABOVE STATED EXPRESS LIMITED WARRANTIES, GSI MAKES NO WAR-RANTY OF ANY KIND, EXPRESSED OR IMPLIED, IN
1004 E. Illinois St., Box 20Assumption, IL 62510-0020phone: 217-226-4421fax: 217-226-4420www.grainsystems.comOctober 1998REVISED August 2004
4Service Platform & StiffenerINSTALLATION & SAFETYWARNING! BE ALERT!Personnel operating or workingaround equipment should read thismanual. T
5Service Platform & StiffenerPLATFORM INSTALLATION
6Service Platform & StiffenerPLATFORM INSTALLATIONAirstream service platform units aredesigned for use with Airstream twoand three module grain dr
7Service Platform & StiffenerPLATFORM INSTALLATIONFigure 4: Attaching side channels.Figure 3: Bolting reinforcement plate to main support channel.
8Service Platform & StiffenerPLATFORM INSTALLATIONFigure 5: Placing rear tie angle on platform.5. Position the rear angle tie, D01-2034, and conne
9Service Platform & StiffenerPLATFORM INSTALLATIONFigure 7: Close-up of rear portion of frame.Figure 8: Attaching front channel.
Kommentare zu diesen Handbüchern