PNEG-1722Series II Sweep Protected Cord Slip Ring SumpInstallation ManualPNEG-1722Date: 12-07-09
2. Safety10 PNEG-1722 Series II Sweep Protected Cord Slip Ring SumpOperate Unload Equipment Properly• Untrained operators subject themselves and othe
2. SafetyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 11Operator QualificationsA. The User/Operator must be competent and experienced to op
12 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump3. DecalsThe below Figure show the location of the decals and safety signs which should appe
3. DecalsPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 13A. DANGER Sign No. DC-1395 was supplied with your bin unloading equipment. This saf
14 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump4. Assembly1. Assemble the slip ring shield onto the cross brace assembly using four (4) 1/4
4. AssemblyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 153. Once the assembly is aligned properly, attach the cross brace to the sump with
4. Assembly16 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump9. Feed the nine (9) stranded wires from the slip ring through the vertical pivot
4. AssemblyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 1715. Wire the multi-conductor cord to the slip ring using the fork terminals provi
4. Assembly18 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump20. Make sure that the lower shroud assembly and the drilled conduit exit hole in
4. AssemblyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 19Figure 4G 27. Attach one 1" liquid-tight flex conduit coupling to each end o
2 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump
4. Assembly20 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump30. Feed the nine (9) stranded wires from the slip ring through one of the holes
PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 215. Start-upPreform Pre-start Checks1. Make sure ALL shields are in place.2. Inspect the coll
22 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump6. MaintenanceMaintain the Hopper1. Use caution when repairing or replacing equipment parts.
6. MaintenancePNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 23Brushes1. Inspect for wear. If the distance from the top of the insulator to t
6. Maintenance24 PNEG-1722 Series II Sweep Protected Cord Slip Ring SumpFigure 6B Brush Springs1. Inspect and test brush springs to assure uniform bru
6. MaintenancePNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 25Rings1. Inspect the ring surface for dirt, oxidation or other contaminants. A
26 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump7. TroubleshootingProblem Possible Cause SolutionSweep will not run.1. Power cords may be un
PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 27NOTES
28 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump8. Parts ListComponents
8. Parts ListPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 29Components Parts ListSystem Ref # Part # DescriptionALL 1 GC04615 Standard 15K
Table of ContentsPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 3ContentsChapter 1 Introduction ...
8. Parts List30 PNEG-1722 Series II Sweep Protected Cord Slip Ring SumpSlip Ring Replacement PartsSlip Ring Bore SizeBrush HoldersZ A B, C, D E, F, G,
PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 319. WarrantyGSI Group, LLC Limited WarrantyThe GSI Group, LLC (“GSI”) warrants products which
This equipment shall be installed in accordance with the current installation codes and applicable regulations which should be carefully followed in a
4 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump1. IntroductionProduct Information1. The Series II Sweep hopper with collector ring includes
1. IntroductionPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 5Slip Ring IntroductionSlip rings must be enclosed and protected from any conta
6 PNEG-1722 Series II Sweep Protected Cord Slip Ring Sump2. SafetySafety GuidelinesThis manual contains information that is important for you, the own
2. SafetyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 7Safety InstructionsOur foremost concern is your safety and the safety of others asso
2. Safety8 PNEG-1722 Series II Sweep Protected Cord Slip Ring SumpInstall and Operate Electrical Equipment ProperlyElectrical controls should be insta
2. SafetyPNEG-1722 Series II Sweep Protected Cord Slip Ring Sump 9Wear Protective ClothingWear close fitting clothing and safety equipment appropriate
Kommentare zu diesen Handbüchern